機床商務網(wǎng)
詳細介紹
 | ① 潤滑時間 Lubrication timing | |
| ② 間歇時間 Intermittent timing | ||
| ③ 端子座 Terminal base | ||
| ④ 入油口 Oil inlet | ||
| ⑤ 壓力表 Pressure | ||
| ⑥ 馬達 Motor | ||
| ⑦ 出油口 Oil outlet |
| ? | 先調整輸油(ON)和停止(OFF)時間，依使用電壓輸入電源，輸油時間開始計時(0-120S可調)，繼電器接點導通馬達運轉開始輸油，計時到馬達停止運 轉，此時轉入停止時間開始計時(0-180M)，依此模式做輸油和停止輸油動作，本計時器另備有壓力和液位兩組空接點。本給油機設有保護裝置，壓力過載時 自動洩壓，壓力開關能了解管路壓力狀態(tài)，浮動開關景式油箱中的油位。 ※注意事項：接電源時請查明本機的電壓是否正確，請勿使用回收油，避免雜物阻塞油路，內外油網(wǎng)請定時清洗（約三個月） |
| ? | Adjust the oil feeding (ON) & stop (OFF) timer. Connect with appropriate power supply, Start timing the oil feeding (0-120S adjustable). Motor starts, running to feed the lubricating oil after relay is connected and keep on feeding the oil unti the seffing time is up. Then begin counting the stop, feeding timel (0-180M). Operation of oil feeding and stop oil feeding is according to the above mode. Equipped with protector, auto pressure releases switch floating switch for knowing the pressure in the oil pipe and oil level of tank. Connect with appropriate power and do not use recovered oil and clean the filter periodically once every three months to avoid oil pipe being blocked. |
| TYPE | TK-1203 | TK-1203A | TK-1203E | TK-1203AE | |||
| 流量 Max.Flow | 180cc/min | 180cc/min | 180cc/min | 180cc/min | |||
| 壓力 Pressure | 5~15kg/c㎡ | 5~15kg/c㎡ | 12~15kg/c㎡ | 12~15kg/c㎡ | |||
| 浮球開關 Float Swith | ● | ● | ● | ● | |||
| 油箱容量 Oil Tank Capacity | 3L . 4L . 8L | ||||||
| 管路壓力訊號裝置 Oil Pipe Pressure Signal | 選配 Take Your Choice | ||||||
| 釋壓保護裝置 Pressure Protection Device | ● | ● | ● | ● | |||
| 潤滑時間 Lubricating Timing (min) | 1-120秒 (sec) | 1-120秒 (sec) | |||||
| 間歇時間 Intermittent Timing (min) | 1-180分 (min) | 1-180分 (min) | |||||
| 電壓 Voltage (50/60Hz) Single Phase | 110v or 200v 單相 | 110v or 200v 單相 | 110v or 200v 單相 | 110v or 200v 單相 | |||
| 馬達出力功訊率 Consumption Power | 20W | 20W | 20W | 20W | |||
| 脫壓裝置 (E) Pressure Relief Divice | ● | ● | |||||
| 接頭口徑 Joint Dia | 4Φ or 6Φ | 4Φ or 6Φ | 4Φ or 6Φ | 4Φ or 6Φ | |||
| ※備註 (Remark) | 配合比例式分油座使用 Use Proportional Oil Distribution | 配合容積式分油座使用 Use Content Type Oil Distribution | |||||
機床商務網(wǎng)